Interposers. EMIB. Foveros. Die-to-die stacking. ODI. AIB. TSVs. All these words and acronyms have one overriding feature – they are all involved in how two bits of silicon physically connect to each other. At the simple level, two chips can be connected through the printed circuit board – this is cheap but doesn’t allow for great bandwidth. Above this simple implementation, there are a variety of ways to connect multiple chiplets together, and TSMC has a number of these technologies. In order to unify all the different names it gives to its variants of its 2.5D and 3D packaging, TSMC has introduced its new overriding brand: 3DFabric.

3DFabric makes sense as a brand to tie the dozen or so combinations of packaging technology that TSMC offers. Broadly speaking, 3DFabric is split into two segments: on one side are all the ‘front-end’ chip stacking technologies, such as chip-on-wafer, while the other side is the ‘back-end’ packaging technologies such as InFO (Integrated Fan-Out) and CoWoS (Chip-On-Wafer-On-Substrate).

Even with this arrangement of TSMC’s technologies, it still introduces a lot of acronyms for users not familiar with packaging offerings. Some of them aren’t always obvious either, such as RDL or LSI, especially for those that are used to Intel’s brand names for the packaging technologies it has. Hopefully we can deconstruct what these terms and compare them to offerings at other foundries.

TSMC-SoIC: Front-End Chip Stacking

The front-end chip stacking technologies, such as chip-on-wafer and wafer-on-wafer, are collectively known as ‘SoIC’, or System of Integrated Chips. The goal of these technologies is to stack bits of silicon on top of each other without using the ‘bumps’ that we see on the back-end integration options. Here, the SoIC designs are literally creating bonding interfaces such that silicon can sit on top of silicon, as if it was a single piece of silicon to begin with.

This is a technically more complex procedure, and the benefits often lie in thermal performance:

This slide shows that the thermal resistance of a face-to-face SoIC bond is up to 35% lower than a micro-bump connection, and as we move into the future of compute with multiple packaged chips, managing those interfaces for thermals is going to be tough. The downside of these SoIC technologies however is that the stacked design has to be co-designed with each other – microbump technologies, such as EMIB, are done in such a way that technically a range of chips could be connected together. Using SoIC, as chip-on-wafer or wafer-on-wafer, the designs are fixed in from the start.

Nonetheless, TSMC is keen to promote its SoIC chip stacking abilities, with a demonstration of a 12-layer stack as part of the slide deck. You can read our separate coverage of this in our news article.

Naturally there is concern about connecting two bits of silicon without micro-bumps, such as density and reliability. TSMC states that they can demonstrate reliable 0.9 micron bond pitches in a very reliable format. If we compare that to the best bump pitch stacking that Intel has on its roadmap, the company is aiming for 10-micron bump pitches, which is an order of magnitude higher. In this case, for the chips where it makes sense, SoIC offers better connectivity density and lower energy-per-bit.

TSMC is planning to offer SoIC options on its N7, N5, and N3 process nodes, with the TSV pitches scaling down  from 9 micron to 4.5 micron in that time. TSMC is expecting a regular cadence to this release schedule, with options appearing approximately 6-12 months after each respective node moves into high volume manufacturing.

TSMC Back-End Advanced Packaging

Competing against EMIB and Foveros

The other element in packaging is the simpler end of the spectrum: connecting two silicon die on a single package. This is usually done with the two pieces of silicon side-to-side, with a variety of ways for connection.

The one that most people are familiar with is the interposer method, where a large piece of silicon sits underneath all the interconnected dies, and acts as a faster routing method than simply laying traces through a PCB package.


NEC SX-Aurora TSUBASA with 6 HBM2 Stacks

The other method is, in similar terms, interposer technology, however the interposer is embedded in the PCB and is only used to connect one specific die to another (this is what Intel calls its Embedded Multi-Die Interconnect Bridge, or EMIB).


Intel's equivalent EMIB solution

The third is direct die-on-die vertical stacking, however this is different to the SoIC implementations mentioned above due to the use of micro-bumps between the two pieces of silicon, whereas SoIC uses bonding. In fact, all of the implementations in this second half of TSMC’s offerings are micro-bump based – this allows for better mix and match scenarios between different chips after each chip is made, however it doesn’t get the benefits of density or power that SoIC provides.

This is why it’s called ‘back-end’ advanced packaging – take for example, a HBM-enabled GPU.

A number of HBM-enabled GPUs have a single GPU die, several HBM die, all placed on top of an interposer. The GPU and HBM are made by different companies (and even different HBM could be used), while the silicon interposer can also be made elsewhere. This silicon interposer can be passive (contain no logic, only die-to-die routing), or it can be active, and designed to be a better network interconnect between chips if required, although this means the interposer would consume power.

TSMC’s GPU-like interposer strategy has historically been called CoWoS – chip-on-wafer-on-substrate. As part of 3DFabric, CoWoS now has three variants depending on the type of implementation.

The standard one everyone is familiar with is being called CoWoS-S, where S stands for Silicon Interposer. The limit of CoWoS-S is all in the size of the interposer, which is often built on a 65nm manufacturing process or similar. As the interposer is a single piece of silicon, it has to be manufactured similarly, and as we move into a chiplet era, customers are asking for bigger and bigger interposers, which means TSMC has to be able to manufacture them (and give high yield). Traditional chips are limited by what is known as the size of the reticle, which is a fundamental limit inside of a machine as to how big it can ‘print’ a layer at a single instance. In order to enable products whose chips are on the reticle size, TSMC has been developing multi-reticle sized interposer technology, allowing these products to be big. Based on TSMC’s own roadmaps, we are expecting CoWoS implementations in 2023 to be around 4x the size of the reticle, allowing for over 3000+ mm2 of active logic silicon per product. We have a news item specifically covering this technology that you can read here.

Due to CoWoS-S being a popular implementation for the ASIC+HBM crowd, TSMC is also implementing a technology track called CoWoS-S STAR, for STandard ARchitecture. This will allow customers to work within specific design protocols for 2/4/6 HBM stacks, minimize the size of the interposer, but also speed up time to market and improve yield.

CoWoS-L is another variant, using local silicon interconnects and a redistribution layer. The key word here is ‘local’, meaning that it connects two silicon die together locally. This is going to be TSMC’s approach to Intel’s EMIB. While Intel’s EMIB is already in use for several products (Kaby-G, Stratix 10, Agilex FPGA), TSMC is only currently in pre-qualification right now. The way TSMC seem to be implementing CoWoS-L is by placing all of the bridge interconnects onto a package at once, and so the technology is limited by the furthest distances away from each of the interconnects. As in the slide below, TSMC is aiming for 3.0x reticle for CoWoS-L in Q2 2021.

InFO (Integrated Fan Out) packaging allows chips to ‘fan out’ additional connections outside the standard floorplan of an SoC. This means that while a chip logic area can be small, the chip is made bigger than the logic to accommodate all the required pin-out connections. TSMC has been offering InFO for a number of years, however under 3DFabric it will now offer different types of InFO related to in-package connectivity.

InFO-R (also known as InFO_oS) allows for a redistribution layer to be added between the die and the microbumps in order to unify multiple die into a single package. This is another technique whereby the limiting factor is the x/y dimensions of the technology, measured in reticle sizes. Currently TSMC supports InFO-R at 1.5x reticle since 2018, and will move to 1.7x reticle in Q4 2020 with 2.5x reticle by Q1 2021.

InFO-L is similar to CoWoS-L in that it uses a localized silicon interconnect to connect multiple InFO dies together. This technology is still a work in progress, with qualification expect to complete in Q1 2021.

TMSC’s packaging technologies can also be combined in the same product. By implementing both front end (SoIC) and back-end (InFO) packaging, new classes of products can be made. The company produced one such mock-up:

On the face of it, TSMC looks set to offer more packaging options for its customers over the coming years. The main competition on this seems to be Intel, who has been able to implement its EMIB and Foveros technologies in a few current products and some to-be-released products. TSMC will have the benefit of working with more projects and customers to help deliver these technologies, in a way that Intel might struggle with. I will hand it to Intel however, the marketing for its technologies is a lot easier to remember. The minute someone says EMIB or Foveros, I know exactly what they’re talking about – with TSMC, just saying ‘3DFabric’ could mean a lot of things, SoIC is pretty clear, but then differentiating between CoWoS-S and CoWoS-L just doesn’t roll off the tongue as easily, and requires another mental step in order to make the connection.

Related Reading

 

 

 

 

 

 

Comments Locked

9 Comments

View All Comments

  • SaberKOG91 - Wednesday, September 2, 2020 - link

    > The downside of these SoIC technologies however is that the stacked design has to be co-designed with each other

    I would disagree that this is a downside. This is no different than providing a footprint for PCB manufacture or microbumps on an interposer. It's a lot more detail, sure, but as long as both companies are comfortable agreeing to that shared interface, it's no big deal. Worth noting that TSMC has the ability to act as the intermediary here to protect trade secrets and the like. There's also no issue here if the entire stacked design is provided by the same vendor. Storage and RAM folks will love this.
  • Duncan Macdonald - Wednesday, September 2, 2020 - link

    There is a penalty in design time - the interconnection layout has to be decided before either chip design can be finished. When an interposer is used however, the interconnection layouts and chip layouts of both chips can be done independently and the interposer matches the chips together - if one chip is later altered then only the interposer needs to change. As the interposer is basically a much shrunk PCB done on an old silicon process (65nm) it is far easier to change than a complex piece of logic done on an advanced process.
  • SaberKOG91 - Wednesday, September 2, 2020 - link

    Right, but TSMC can short-cut this by setting the interfaces for both vendors.
  • edzieba - Thursday, September 3, 2020 - link

    Because SoIC has metal layers projecting /through/ the dies, it needs dedicated die design for that packaging method. You can't just design an interface surface, because all your die logic needs to shuffle around the metal pillars.
  • SaberKOG91 - Friday, September 4, 2020 - link

    I have a BS and MS in Computer Engineering and I've done some pretty decent-sized hand-layouts (~700 transistors on 180nm). The pillars are an inconvenience, but they aren't really any different than designing for pads in a QFN package, wafer-level-packaging (WLP), or microbumps with a uniform grid. It's even less of an issue with how much we rely on synthesis tools to do the routing nowadays. The key advantage that TSMC is offering is a 0.9 um pitch (vs 25 or 40 um for backend) which lets you have a much smaller area for the same number of connections, making routing even easier for logic chips or density higher in the case of memories.

    That said, there's no reason why every layer of the stack would need to have the same set of columns or even have all of them traveling all the way through. That's useful for things like memories where a 3D crossbar is easy to implement and where you can save on economies of scale, but it's not required. You could also add an extra "adapter" layer to the stack to route from one interface to another if chips have different interfaces.
  • Alexsuns - Wednesday, September 2, 2020 - link

    It's useful information. I think it'll be popular.
  • name99 - Wednesday, September 2, 2020 - link

    Thanks for this summary, Ian! For some time I've been looking for an overall summary of TSMC's tech in this area.
  • edzieba - Thursday, September 3, 2020 - link

    It's never been exactly clear what InFO actually /is/. From the marketing side, it just looks like putting an extra substrate layer or silicon interposer on the package, but is for an unknown reason given a different name. For example, you have both CoWoS-L and InFO-LSI, both of which are a set of dies stacked on a silicon interposer stacked on a substrate, but with no clear indication of why the two are different.
  • name99 - Thursday, September 3, 2020 - link

    CoWoS handles larger devices (just under reticle up to multiples of reticle).
    InFO is for smaller devices, up to reticle and no larger.

    To me it looks like to some extent they're solving the same problem: "I want to place two chips side by side". But once you actually try to solve that problem many questions arise: how fast does the connection need to be? how much heat dissipation? how much area? etc etc.
    Less demanding versions of these answers (think cell phone) allow for one specific way of solving the problem which is cheaper but less performant and can't scale up (InFO); if that's not good enough you can alternatively use the more expensive CoWoS.

    How EXACTLY are they different? As far as I can tell the most significant difference is that the physical layer carrying the RDL is organic for InFO, as opposed to Si for CoWoS. Organic means you can flow it then bake it -- easier and cheaper than dealing with super-thin pieces of Si as you need to for CoWoS.

    TL;DR TSMC can solve your 2.5D needs, whether they are cheap and low power (eg watch/phone) or expensive and high power (eg discrete GPU).

    Corrections welcome!

Log in

Don't have an account? Sign up now