Gigabyte G1.Sniper 3 Overview

Based on our Gigabyte Z77X-UD5H review, if we extrapolate up to the G1.Sniper 3, then we should be in for a real treat.  In our testing, the Gigabyte G1.Sniper 3 did definitely throw up a few surprises, and given the feature set, is one of the more competitive price versus functionality motherboards in this combined review.

Visually on its own, the G1.Sniper 3 has a good balance on green and black on the motherboard, however this may me a lost aesthetic inside a case with a lot of PCIe devices inside it – the intended market for this product.  The G1.Sniper 3 aims at gamers, specifically those who want an Ivy Bridge platform setup as well as two or more GPUs.  With the PLX chip, it also performs at peak x8/x8/x8/x8 GPU setups, wired such that in dual usage it retains x16/x16.

The G1.Sniper 3 currently retails for $280 on Newegg, and for the money there is a lot of added functionality that people will use.  We have one Killer NIC for gaming, an Intel NIC for networking features, a Creative CA0132 audio chip, an mSATA port, a total of ten USB 3.0 ports, all four video outputs and a PS/2 port all wrapped up in an E-ATX form factor (one inch wider than ATX).

The package really shines when we open the box, which contains a WiFi PCIe x1 card, dual antenna, eight SATA cables, a USB 3.0 front panel and rigid SLI connectors.  There is a little question mark over the choice to include a WiFi card, given the system already has increased cost due to the dual Killer/Intel NIC scenario.

Performance also gives us an extra point to think about.  Some Z77 manufacturers are taking advantage of what has been called ‘MultiCore Enhancement’, where instead of running an i7-3770K CPU at 39x/39x/38x/37x during 1/2/3/4 threaded load, the CPU will run 39x/39x/39x/39x.  Gigabyte does this on their main channel boards, the UD3H and UD5H.  They go a step further on the G1.Sniper 3, by providing a default overclock at any load to 40x (it will idle at 16x).  This gives the G1.Sniper 3, out of the box, essentially a clean sweep in all our CPU tests.  It sometimes translates in our GPU testing as well.  But without an overclock, the G1.Sniper 3 is the first board to come with a ‘better than the highest Turbo multiplier’ overclock.

Visual Inspection

The first thing to notice about the Gigabyte G1.Sniper 3 is the size of the board.  It is one of two boards in this roundup that uses the E-ATX form factor, which means that there is an extra inch of width to the motherboard.  This allows Gigabyte to place a larger chipset heatsink if it wanted, more controllers, or an improved layout.  Real estate is often a premium on a high end product, so jumping up to the next motherboard size can make sense given most gamers this product is aimed at will have full sized ATX cases.

The green and black livery is accented by a gold skull and knife on the chipset heatsink.  All the heatsinks are solid and finned, designed to take air in one direction each to aid cooling, and are also connected by heatpipes in order to distribute the heat away from the warm areas.  The socket area is surrounded on three sides by these heatsinks, which measure ~30mm up from the PCB at the highest point, though they are set away from the Intel minimum designated socket area.  The socket area has access to three fan headers nearby – a system 4-pin fan header to the top left near the 8-pin CPU power connector, a CPU 4-pin fan header to the right of the top heatsink, and a second 4-pin system fan header next to the two-digit debug button on the right.

Along the right hand side of this 6-layer PCB (there is a number on the reverse bottom of all GB boards that tells us this) are a large number of connectors that Gigabyte have added with the extra PCB space we have.  At the top is a trio of power/reset/ClearCMOS buttons, with the power button being big and red.  I would like Gigabyte in the future to make the reset button distinct as well, such that enthusiasts will not accidentally be clearing their BIOSes instead of resetting their systems.

Underneath this is a two-digit debug display, useful for diagnosing POST issues and a series of voltage read points if users are willing to solder on their own meters.  Beside the 24-pin ATX power supply is a USB 3.0 header, powered by a nearby VIA chip.  This header is in the perfect place for the USB 3.0 front panel included in the box - the VIA chip also powers the USB 3.0 header at the bottom right of the board.  Beside the SATA ports we have a SATA power connector, for supplying more power to multi-GPU setups on board.  I prefer having this type of connector here, as opposed to the molex or 6-pin connectors we sometimes find just above the PCIe slots.

Gigabyte have thankfully split their SATA ports by color, making them easier to understand – the white ports are the chipset SATA 6 Gbps ports, the black are the chipset SATA 3 Gbps ports, and the grey are the SATA 6 Gbps powered by two Marvell controllers.   The mSATA port just beside the normal SATA ports shares lanes with one of the chipset SATA 3 Gbps ports, so it is something to bear in mind if you are using an mSATA device.

The bottom of the board on most motherboards is often populated with USB 2.0 headers (as the Z77 chipset allows a lot of them) or power/reset buttons, but typically Gigabyte takes a different approach.  Here Gigabyte are using a VIA VT6308P chip (the really big one at the bottom left) to power two IEEE1394 headers, should anyone require these ports.  Alongside these are two USB 2.0 headers, the front panel header section, a BIOS switch (to go between the two onboard BIOSes), a pair of fan headers, and a TPM module.  As we have discussed in previous Gigabyte reviews, Gigabyte like to add a TPM module as it is often requested by their business partners.  How useful it may be on the top of their range gaming board, I am not sure.

The PCIe ports are what all these motherboards reviewed today are all about, and Gigabyte point out which ones are for GPUs with the bright green color.  By using the PLX PEX 8747 chip underneath the middle heatsink, the PCIe lanes are split such that:

One GPU: x16/-/-/-
Two GPUs: x16/-/x16/-
Three GPUs: x16/-/x8/x8* or x8/x8/x16/-
Four GPUs: x8/x8/x8/x8*

*These configurations use a GPU in the bottom PCIe slot.  If the GPU is dual slot, it could restrict some of the space available for these bottom headers, such as my power connectors shown here:

The audio on the G1.Sniper 3 is one point which sets this board apart from the others in this review – Gigabyte have decided to use a Creative CA0132 chip, separated in its own area of the PCB with an EM shield to help reduce interference.  The chip is also accented with audio-specific Nichicon capacitors, which are reputed to be better than the standard audio caps used.

The rear IO panel is covered in a myriad of features – from left to right we have a combination PS/2 port, two USB 3.0 ports, D-Sub, DVI-D, DisplayPort, HDMI, four more USB 3.0 ports, an Intel 82579V NIC, a Qualcomm Atheros Killer NIC (2201-B), audio jacks and a S/PDIF output.  While Gigabyte has included all the video outputs, legacy is partly in the mind with D-Sub and PS/2 here.  There is no USB 2.0, which makes life difficult as only some of the USB 3.0 ports work on first install of an OS – two of the six should work as they are based off the chipset.  However, here is another point – Gigabyte have two VIA USB 3.0 controllers on board for 8 USB 3.0 ports, and the chipset should provide four more to make twelve in total.  But Gigabyte only uses two from the chipset, as per their chipset diagram.

Board Features

Gigabyte G1.Sniper 3
Price Link
Size ATX
CPU Interface LGA-1155
Chipset Intel Z77
Memory Slots Four DIMMs, Supporting up to 32GB DDR3
1066-2666 MHz, Non-ECC
Video Outputs D-Sub
Onboard LAN Qualcomm Atheros Killer E2200
Intel GbE
Onboard Audio Creative CA0132
Expansion Slots 2 x PCIe 3.0 x16 (x8 when slots underneath are occupied)
2 x PCIe 3.0 x8
2 x PCIe 2.0 x1
1 x PCI
Onboard SATA/RAID 2 x SATA 6 Gbps (Intel), Supports RAID 0, 1, 5, 10
4 x SATA 3 Gbps (Intel), Supports RAID 0, 1, 5, 10
1 x mSATA 3Gbps (Intel) shared with SATA2_5
4 x SATA 6 Gbps (Marvell 9172), Supports RAID 0, 1
USB 2 x USB 3.0 (Intel) [2 back panel]
8 x USB 3.0 (VIA VL810) [4 back panel, 4 onboard]
4 x USB 2.0 (Intel) [4 onboard]
Onboard 6 x SATA 6 Gbps
4 x SATA 3 Gbps
1 x mSATA 3 Gbps
5 x Fan Headers
2 x USB 3.0 Headers
2 x USB 2.0 Headers
2 x IEEE1394 Headers
Power/Reset Buttons
ClearCMOS Button
BIOS Switch
Voltage Measurement Points
TPM Header
Power Connectors 1 x 24-pin ATX Power Connector
1 x 8-pin CPU Power Connector
1 x SATA Power Connector (for PCIe)
Fan Headers 1 x CPU
4 x SYS
IO Panel 1 x PS/2 Combination Port
6 x USB 3.0
1 x D-Sub
1 x DVI-D
1 x HDMI
1 x DisplayPort
2 x Network Ports (Intel, Killer)
1 x Optical S/PDIF Output
Audio Jacks
Warranty Period 3 Years
Product Page Link

The main features of the Gigabyte G1.Sniper 3 are in terms of functionality against price.  For $280 of your hard earned cash, we get dual NIC (one Intel, one Killer), ten USB 3.0 ports, 10 SATA ports, 4-way SLI and CrossfireX through a PLX PEX 8747 chip, any video output for the iGPU wanted, a TPM module, and improved audio through the Creative CA0132 chip.  For legacy, we have a PS/2, D-Sub, a PCI port and IEEE1394 headers. 

Multi-GPU on Z77 Gigabyte G1.Sniper 3 BIOS


View All Comments

  • mayankleoboy1 - Wednesday, August 22, 2012 - link

    Where are the GPGPU benchmarks? AFAIK, those are affected by the PCIE 3.0 bandwidth, as shown in the HD7970 review.

    Games are more or less happy with a PCIE2.0 x8 .
  • MrSpadge - Thursday, August 23, 2012 - link

    A few GP-GPU apps are affected, most aren't. Even PCIe 3 is slow as hell from the perspective of the GPU, so you try to avoid external communication as much as possible. Reply
  • TimoKyyro - Wednesday, August 29, 2012 - link

    I was hoping to see some GPU rendering too. I'm using CUDA on Blender and I really need more GPU power. It would be nice to know if there is a difference between 4x 680 or 2x 690 on different PCIe setups. Reply
  • extide - Wednesday, August 22, 2012 - link

    Thanks for providing the diagrams of lane routing. I wish ALL manufacturers would supply a diagram with their boards so you know how to set it up when you are building a system. Sadly, these diagrams are the exception, not the rule. :( Reply
  • processinfo - Wednesday, August 22, 2012 - link

    For me only EVGA seems worth consideration (I don’t like a fan on chipset though).

    I have few requirements that others do not meet.

    I want PS/2 keyboard port (don’t care about mouse). I don’t see it as legacy. It is still superior to USB for keyboard. Works on interrupts instead of pulling, allows as many keys pressed without ghosting as you wish (know it probably does not matter in real life but I like that anyway).

    Display port output is mandatory for me these days. While it is true that this kind of mobo will run dedicated graphics card (or more than one for that matter) I like to have output here for possibility to use it with CPU graphics if my graphic cards breaks and needs replacement (I had that happen and waited almost two weeks for new one). HDMI is no go because does not support high enough resolution.

    Gigabyte is out for me because audio chip. Maybe it is better but it does not do 7.1 and I will lose two channels in my Tiamat 7.1 headset.
  • rwpritchett - Wednesday, August 22, 2012 - link

    You should check out some of the newer USB keyboards. I don't know how they do it, but some of them can now do full NKRO without PS/2. My Nighthawk X9 can do full NKRO over USB. Reply
  • processinfo - Thursday, August 23, 2012 - link

    Interesting but this is not possible with standard USB keyboard protocol. If it does that it has to use some tricks and most likely custom keyboard driver.

    Also I have Thermaltake Meka G1 that I like and I purchased because I got tired replacing membrane keyboards so I rather buy motherboard with PS/2 then new keyboard.

    My point is that at this price point and clearly meant for gamers (who else is using more than one graphic card in non-workstation pc) they should think about such details especially when they go overboard with other ports, e.g., who needs all 4 kinds of display output on gaming mobo, or 10 USB ports on back plate alone (if you need plenty you can have them on bracket connected to header).
  • MacGyverSG1 - Wednesday, August 22, 2012 - link

    I loved the review. The G1.Sniper 3 was on my short list for a while. Could get back on, though.

    I'm waiting for the ASUS Maximus V Extreme to get tested next.

    I only need a motherboard to complete my new build. I plan on running this new rig for 6+ years so I want a board that can keep up with the times.
  • just4U - Thursday, August 23, 2012 - link

    I am staying away from the Rampage/Maximus lines from Asus this time out as Gigabyte has pretty much brought better value accross the board on their gamer boards. I don't expect Asus to catch up till the next chipset.. Reply
  • goinginstyle - Thursday, August 23, 2012 - link

    I tried the G1 Sniper 3 and returned it a few days later. The audio was a significant downgrade from the Assassin series, EFI is clunky at best and the board had serious problems with a GSKill 16GB 2666 kit, not to mention the lousy fan controls.

    Purchased a Maximus Formula V and never looked back as the EFI, Fan Controls, Clocking and Audio are much better in every way compared to the Sniper board. There is no way Gigabyte has brought better value than ASUS with the Z77 chipset. You get what you pay for and the GB is overpriced once you actually use the board and compare it to ASUS or even ASRock.

Log in

Don't have an account? Sign up now