External Impressions and Cable Configuration

The rugged and very thick material is strongly reminiscent of the Revolution85+ series. The color is charcoal gray, with a platinum-like surface around the fan grille. The grille has an Enermax logo in the middle, with a Platimax logo and a picture of a crown on both sides of the power supply. Our personal preference is that more is less when it comes to logos and such, but others might appreciate the markings on the case.

The modular plugs protrude slightly at the front of the PSU. The PCIe plug sockets have a different color than the ones for the peripheral components. The cable sleeving is high-quality, but the gold and red stripes on the sleeves don't quite fit with the 80 Plus Platinum certification. While it's not likely important for many users, there will be some that dislike the Platimax aesthetic.

Cables and Connectors

Main 24-pin 55cm fixed
ATX12V/EPS12V 4+4-pin 60cm fixed
8-pin 60cm fixed
PCIe 2x 6/8-pin (50cm) modular
2x 6/8-pin (50cm) modular
Peripheral 4x SATA (ca. 45, 60, 75, 90cm) modular
4x SATA (ca. 45, 60, 75, 90cm) modular
4x Molex (ca. 45, 60, 75, 90cm) modular
4x Molex, 1x FDD (ca. 45, 60, 75, 90, 105cm) modular

The connector configuration is satisfying. Both CPU cables are very long at 60cm. Each of the two PCIe cables reach 50cm. Altogether the model has four PCIe connectors for graphics cards. The eight SATA connectors are not bad for a 750W power rating. The FDD plug, if you still need one, is at the end of one Molex cable harness. The 24-pin and CPU cables are permanently fixed. Enermax prefers a semi-modular connector system for lower wattages; it's only if you buy the 1000W+ models that you get modular mainboard cables. It's an odd distinction, really—are fully modular PSUs someone more for "enthusiasts" that other 80 Plus Platinum power supplies? Does anyone actually detach their CPU/mainboard cables? Regardless, that's how Enermax has chosen to configure this particular model.

Package Contents, Power Rating, and Fan Switching Circuits and Components
POST A COMMENT

47 Comments

View All Comments

  • ssj3gohan - Sunday, February 12, 2012 - link

    In this sentence:

    "(...) This compensates for the slightly higher losses during turn-on (which is no problem with a low resistance between drain and source). (...)"

    you imply that the drain-source resistance has something to do with the switching losses. This is not the case! Let me explain: there are two types of losses associated with power transistors: on-state losses and switching losses. On-state losses are incurred when the transistor is fully on and conducting current; it's simply the drain-source on-state resistance (R(DS, on)) times current squared. Then there's losses associated with the transition from off to on, or from on to off. At this moment, the transistor doesn't instantaneously turn on or off, but enters its linear region. At this time, both high voltage and current exist simultaneously over and through the device, which means P=I*U=high losses. You can't fix this with lower on-state resistance because the transistor is not in its on-state, it is in some state in between. This transient period is only very short (tens of nanoseconds) but if you switch really fast, e.g. 200kHz+ which is what happens in some power supplies, the losses add up quickly. The only way to combat these losses is:

    - Making either I, or U, or both zero at switching time (zero current, zero voltage switching [ZVS, ZCS])
    - Making the transient period as short as possible (which in practice means reducing gate charge or if possible using better drivers)

    That last bit is pretty much a no-go for modern supplies because it causes noise spikes, hence the advent of ZCS and ZVS.
    Reply
  • Martin Kaffei - Sunday, February 12, 2012 - link

    I know. This might be a translation failure.
    The previous sentence is already about turn-on ("switching"), so this one was about the next phase.
    In this case I meant saturation (no sure if this is the correct word in English).
    Reply
  • kenyee - Sunday, February 12, 2012 - link

    I.e., is it small enough to fit in actual HTPC cases?

    86% efficiency at 10% load makes it enticing... :-)
    Reply
  • Lithium466 - Monday, February 13, 2012 - link

    It seems that the 5Vsb rail is not protected, and that overloading it (with more than 4A) will permanently destroy the power supply...
    Have you tried it ? Is is true ?
    Reply
  • ShieTar - Monday, February 13, 2012 - link

    Apparently 20% are specified to be 20% on each rail, for each voltage, (see the qualification test report here: http://www.plugloadsolutions.com/psu_reports/ENERM... ).

    To me, this seems to be a bit less than realistic. In normal day usage, I would expect the 12V rail to be the one that really changes between idle and load cases, with the other voltages remaining at a relatively constant, and rather low, load.

    Would it be possible to test efficiency at a few realistic load cases on top of the ones used by the specification? This would be really interesting to see.
    Reply
  • 86waterpumper - Monday, February 13, 2012 - link

    I agree that alot here run higher end gaming rigs and may use 750 watts of power or even more. I also say that alot here are more likely to have htpcs, servers, and secondary systems somewhere in their house they themselves have built. Then you have the times when a friend or family member wants you to build a system for them to do light tasks. It doesn't always make sense to use a pico type supply for these and there is a gap between say 200 watts and 400/450 watt psus. For all these reasons it is past due time that we get some more efficient lower watt supplies. Right now my main system is a 2500k using the onboard hd3000 video I can play games fine since I have dual older 4:3 monitors still. I currently am using a x-400 seasonic and it's great but I really wish there had been a x-200, 250 or 300 instead.
    There will be a need for high end video cards for those that want to run huge monitors, but as onboard graphics get better and better we will see a shift where people who don't game all the time or want to blow 500 bucks on a video card are content with using onboard. It would be like if chevrolet decided to ONLY make the camaro and corvette fuel efficient and did not care about the compact cars it just does not make sense. I think psu manufacturers are missing the boat in a way but I'm also sure they are afraid that people will not pay a premium for a psu unless it has big watt numbers...
    Reply
  • Iketh - Monday, February 13, 2012 - link

    My thoughts exactly. I'm sick of using 400w power supplies to power 50-100w. I've even thought of the possibility of tapping into the wires or finding splitters for every plug so I can run 2-3 systems off one power supply. Reply

Log in

Don't have an account? Sign up now